Enameled Wire
- Enameled Aluminum Wire
- Enameled Copper Wire
- Copper Strips
- Aluminum Foils
- Paper Covered Wire
- Other Special Enameled Wire
Services
- Corona-resistant enameled wire
- Film Enameled Wire
- Kapton Magnet wire
- Continuously Transposed Conductor
- Fiberglass covered wire
- Paper Wrapped Insulated Winding Wire
- Aluminum Foils
- Transformer Copper Foils
- AWG SWG Enameled Aluminum Wire
- AWG SWG Enameled Copper Wire
Contact
- Zhengzhou LP Industry CO.LTD
- E-mail: office@cnlpzz.com
- Mobile: +86-19337889070
- whatsapp:+86-19337889070
- Tel: +86-371-65861282
- Fax: +86-371-65861123
- Address: No. 86, Jingsan Road, Jinshui Zone, Zhengzhou , Henan Pro. China.
Enameled Aluminum Strip
- international standards winding magnet wire aluminum
- paper insulated copper and aluminum wires venezuela
- class 180 polyamide-imide enamelled aluminum wire
- iso9001 enamelled aluminium wires for motor transformer
- rectangular aluminum electrical wire
- iec standars copper coated aluminum enameled wire
- class 180 polyester imide aluminum enameled wire
- huayuan enameled aluminium wire
- super enameled copper clad aluminum wires for indonesia
- hot sell enameled aluminum wire
- aluminum strip 1050 h18 from china
- high quality swg enameled aluminum wire from china
- ul copper clad aluminum enameled wire
- swg19 enameled aluminium varnished wire
- polyester-imide enameled aluminium wires with ul approved
- new style high conductivity magnet aluminum wire for fan
- uew pew eiw coated copper clad aluminum winding wire
- Sourcing Aluminum Magnet Wire for Mexico: Qualify the Route
- nema standard round aluminium enamelled winding wire
- winding large wire and cable corrugated steel reel
- build heavy transelectric aluminum enameled wire
- ul certification of class 220 enameled aluminium wire
- super enameled copper clad aluminum wires heater coil
- 0.1mm aluminium enameled winding wire
- the leading supplier of awg23 magnet winding wire
Enameled CCA Wire for Saudi Arabia: Confirm the Build
What a Saudi buyer should identify first
Enameled copper-clad aluminum, or CCA, is a bimetal conductor with an aluminum core, a metallurgically bonded copper outer layer, and an electrical enamel coating. The three layers have different jobs. Aluminum provides much of the cross-sectional area at lower mass than solid copper, copper forms the surface contacted by winding terminals, and enamel separates adjacent turns. A request for SWG enameled CCA wire for Saudi Arabia therefore needs more than a gauge number and a destination. It needs a defined conductor construction, an insulation build, an intended coil and evidence that the chosen termination survives service.
The original listing mixed seller snippets and prices without identifying a usable winding design. A buyer should ask whether the intended use is a transformer, a motor, a small solenoid or another component. These applications do not impose identical thermal, mechanical or joining demands. A quote can be commercially attractive while still offering the wrong metal ratio, enamel chemistry or spool format. Treat the drawing and application profile as the technical baseline.
Confirm the copper layer rather than relying on the name
CCA is not interchangeable with copper wire merely because its outside looks copper-colored. Ask the supplier to state how the core and cladding are made, the nominal copper fraction or other agreed construction measure, and the method used to verify it. The purchase contract should specify whether a change in cladding thickness is permitted. Cross-sectional microscopy, mass-based checks or a mutually agreed test can support the declared construction; a photograph of the outside cannot.
Request evidence from the same size range and process route as the order. A coarse sample may be easier to produce than a thin conductor that must travel through tight guides. Examine the surface for exposed aluminum, irregular copper coverage and scoring after drawing. If the winding requires a soldered connection, qualify that exact joint rather than assuming copper-colored surface alone guarantees solderability. The thermal cycle and mechanical restraint of the finished component may make a laboratory joint look better than the production joint.
Translate SWG into dimensions that can be inspected
Standard Wire Gauge is a diameter designation, not a complete magnet-wire specification. State the requested SWG number and its agreed nominal bare diameter in millimeters on the purchase order. Then identify allowable bare-diameter tolerance and whether the gauge applies before or after enamel. A buyer who orders only by gauge can receive wire that does not fit the winding window because two vendors interpret insulation build differently.
The finished outside diameter should be checked across each shipment with a method suitable for the size and coating. Enamel can be eccentric, so rotate the sample and measure at several locations along the reel. A single reading near the free end can miss variation after a production splice or a change in coating speed. For a compact coil, calculate the cumulative effect of the finished diameter over the designed layers. Even a small increase per turn may prevent the last layer from seating.
Specify the enamel system for actual heat exposure
The required thermal class must come from the component insulation design, not from an attractive catalog label. Ask for the resin family, build grade, nominal and maximum finished dimensions, and supporting test method. A temperature class describes long-term insulation-system expectations under defined tests; it is not permission to operate every coil at that number. Hot spots, duty cycle and cooling determine the practical limit.
Compare dielectric breakdown, continuity, adhesion and flexibility on wire from production reels. A conductor can pass a straight-wire voltage test but crack when bent around a small former. Conversely, a thick film that improves an isolated electrical measurement may consume winding space or make termination harder. The best choice balances the actual bend radius, coil voltage and manufacturing yield. Keep the sample and production coil tied to the same enamel recipe and curing settings through change control.
Establish resistance and loss targets with the design team
The electrical resistance of CCA depends on conductor area and its composite structure. Do not substitute a copper resistance table or assume that the copper layer turns the entire cross-section into copper. Define resistance per unit length at a stated reference temperature and set an acceptance tolerance that corresponds to winding performance. Temperature correction is essential when samples are measured in a warehouse warmer than the engineering laboratory.
Model the finished winding, including turns, mean turn length, lead length and the anticipated operating temperature. Compare calculated losses against cooling capacity and the allowed temperature rise. If this is a proposed substitution for solid copper, qualify the complete design rather than silently changing the raw material in an approved bill of materials. A lower reel price has no value if copper-equivalent geometry was assumed and the finished unit overheats or fails an efficiency target.
Test the winding and the terminals together
Run a small but representative coil trial on the intended machine. Record wire tension, guide wear, traverse setting, bend radius and any stops caused by breakage. Inspect the first, middle and last wound layers. A smooth outer surface does not prove the inner layers were undamaged. Count scraped turns, pinholes and rejected joints, and keep the results by reel so the buyer can distinguish a process setting problem from a material lot problem.
CCA termination deserves its own work instruction. Confirm stripping method, connector material, crimp or weld setting, contact resistance and pull strength. Examine the joint after heat cycling and environmental exposure representative of service. If a solder process is proposed, verify wetting and strength after the actual enamel removal process. Protect exposed aluminum at cut ends from moisture and incompatible contacts where the assembly design requires it. Acceptance should cover repeatability across operators, not merely one successful prototype.
Plan for Saudi operating and logistics conditions
The destination does not itself set a universal wire grade. Discuss where the finished product will operate: an indoor appliance, a sealed motor, a ventilated cabinet or equipment exposed to high ambient temperature and dust. These environments have different cooling and contamination risks. The component designer should provide the temperature profile and any enclosure-specific validation. The wire supplier should not promise outdoor or regional suitability from a shipping address alone.
For shipment, identify the importer, delivery term, destination port or inland point, and required commercial documents before pricing. Agree on invoice description, country-of-origin statement, packing list, batch identification and any buyer-specific certificate request. Verify current import requirements with the Saudi importer or customs adviser; document requirements can change and may depend on the final product classification. Keep the trade documents consistent with the physical reel labels, especially material identity and size.
Protect wire quality between factory and winding line
Reel design matters for long-distance transport. Specify flange diameter, barrel diameter, maximum reel mass, winding direction and permissible traverse pattern. A package that lowers freight cost by overfilling may create flange damage or tangled payout on the buyer's machine. Ask for a protective outer package that limits moisture, abrasion and impact while allowing receiving staff to inspect labels without opening every reel.
The receiving plan should sample multiple reels and positions, not just one convenient reel. Verify label, conductor diameter, finished diameter, resistance and visible coating quality against the order. Record packaging damage before unwinding. Store reels under documented conditions, rotate stock by batch and retain a reference sample if traceability is important to the end customer. If a shipment combines manufacturing lots, the paperwork must make the boundaries visible rather than presenting one aggregate test number.
Compare CCA with aluminum and copper alternatives
Solid aluminum magnet wire may suit some cost-sensitive designs, but its terminals and required area must be engineered for aluminum. Solid copper wire offers different conductivity, mass and joining behavior. CCA occupies another design space: it cannot be assumed to deliver the full electrical behavior of copper or the simplest purchasing economics of aluminum. Compare candidates on the same finished-coil drawing, temperature-rise limit, terminal technology and winding yield.
The relevant commercial measure is cost per accepted component, including conductor consumption, scrap, extra processing and field risk. If a CCA design needs larger size or a different winding count, include those design changes. A nominal price per kilogram also obscures the different mass per unit length. Ask for price per specified length or calculate the length yield from verified dimensions and construction. This makes offers easier to compare without overstating a raw-material saving.
Define evidence before approving a supplier
Ask for a construction drawing, declared conductor material, enamel identification, routine test methods and lot-level results. The supplier should identify where conductor drawing and enameling occur and which steps are subcontracted. A certificate should name the actual product and production location; a general company brochure is not evidence that a particular wire size has been qualified. If a recognized standard or listing is required, verify the exact scope and edition independently.
Agree on a controlled sample, an approval report and a notification rule for changes to core stock, cladding, enamel, curing equipment or manufacturing site. Identify what triggers a new winding trial. This matters because a coil that runs well on one pilot reel can behave differently when a high-volume line changes lubricants or take-up tension. Set a practical claim procedure with retained samples and batch records so any defect can be investigated against the material actually used.
Build a quote that engineers and procurement can both use
Send the bare SWG diameter conversion, metal construction requirement, enamel build, resistance limit, thermal target, intended application and annual volume. Add reel drawings, test report format, shipment destination and any mandatory documentation. Request separate prices for samples, trial quantity and routine orders, with lead times and the validity of raw-material pricing explained. A supplier can then quote a defined product instead of filling unknowns with a generic catalog wire.
Ask the engineer to approve the sample after a representative winding and terminal test, while purchasing checks the matching commercial specification. Record the approved sample ID and revision in both systems. For a related size reference, see the AWG and SWG enameled aluminum wire range. The round aluminum magnet wire specification guide helps frame dimensional questions, and the fine copper-clad aluminum wire guide addresses smaller CCA constructions. Confirm each linked product's applicability before borrowing its dimensions for this order.
Frequently asked questions
Is an SWG number enough to release an order? No. Include the agreed bare metric diameter, tolerance, finished diameter, coating system and resistance target. Is CCA the same as solid copper in a winding? No. The core and copper layer must be represented in electrical and terminal qualification. Can a supplier's price sheet confirm compliance in Saudi Arabia? No. The importer must confirm current documentation and product-specific requirements. Does a successful wire test replace a finished-coil trial? No. Machine handling and joint reliability are essential parts of approval.
Before mass production, ask both parties to sign the final construction and inspection plan. Keep the approved reel, laboratory results and winding report traceable to the same revision. This closes the gap between a plausible online listing and a wire that can be purchased repeatedly, shipped correctly and wound into a reliable component.
Previous:flat aluminum enameled winding wire price for transformer
Next:1.33 mm Aluminum Magnet Wire in Air-Conditioner Motors